Expresso front wheel rebuild

Discuss all things 1970 & later Airheads right here.
User avatar
DucatiPete
Posts: 257
Joined: Sun Aug 15, 2010 3:10 am

Re: Expresso front wheel rebuild

Post by DucatiPete »

if ya reckon a DI would help i could send one up tomorrow...
Mal S7
Posts: 661
Joined: Thu Aug 05, 2010 5:26 am

Re: Expresso front wheel rebuild

Post by Mal S7 »

DucatiPete wrote:if ya reckon a DI would help i could send one up tomorrow...
Thanks for the offer Pete. If you lived just down the road I would be straight over. S'OK I will manage.
Have to wait now on my parts order from Motobins. Fork seals, gaiters, caliper seals, brake pads ...
Mal S7
Posts: 661
Joined: Thu Aug 05, 2010 5:26 am

Re: Expresso front wheel rebuild

Post by Mal S7 »

Getting the calipers apart was a challenge. I took them from my R100S spares bike, its brakes were tragic and since I took it off the road the parts have sat around for 5 years. I searched the forum and found a tip to heat the caliper and then use compressed air. Piston sure pops out with a bang .... there are probably safer ways?

Image
008

ps Any opinions on pitting of the piston? One is too far gone, but the other (pic) only has some pits above the seal line.
User avatar
DucatiPete
Posts: 257
Joined: Sun Aug 15, 2010 3:10 am

Re: Expresso front wheel rebuild

Post by DucatiPete »

"the other (pic) only has some pits above the seal line."
If it's as you say should be good to go i reckon... but then again i've never seen the insides of those calipers before.
I see m'bins has newies for £82.50, not cheap... but you only have one per caliper... and it that fails then... hmmm... if it t'was me i'd be happy 'nuf to use the corroded pistons AS LONG AS THE PITTING IS WELL AWAY FROM THE SEALS!
Mal S7
Posts: 661
Joined: Thu Aug 05, 2010 5:26 am

Re: Expresso front wheel rebuild

Post by Mal S7 »

Thanks Pete, the twin disc set-up may be deferred a while now
while waiting for my parts from the UK I note this ...

Image
001

That's the chrome worn off the lower part of my left fork leg. I had the other one hard chromed & ground ten years ago and this one was marginal then. I think this time I might buy a new pattern stanchion from Motobins. About $160AUD plus postage. Italian made, anyone else tried them?
ME 109
Posts: 7306
Joined: Tue Aug 03, 2010 3:00 am
Location: Albury, Australia

Re: Expresso front wheel rebuild

Post by ME 109 »

A bit of silver frost Mal and she'll be right to go!
Lord of the Bings
Motorhead
Posts: 391
Joined: Mon Aug 09, 2010 8:30 pm

Re: Expresso front wheel rebuild

Post by Motorhead »

ME109 what is silver frost? in American-eese
User avatar
dougie
Posts: 2540
Joined: Wed Aug 04, 2010 6:19 pm
Location: Burlington Ontario, Canada

Re: Expresso front wheel rebuild

Post by dougie »

Motorhead wrote:ME109 what is silver frost? in American-eese
I think it is what Jeff uses on his hair. :P
I've spent most of my money on women, motorcycles, and beer.
The rest of it I just wasted.
Mal S7
Posts: 661
Joined: Thu Aug 05, 2010 5:26 am

Re: Expresso front wheel rebuild

Post by Mal S7 »

Image

Wish it was so simple.

And still laughing at what Dougie wrote!
ME 109
Posts: 7306
Joined: Tue Aug 03, 2010 3:00 am
Location: Albury, Australia

Re: Expresso front wheel rebuild

Post by ME 109 »

dougie wrote:I think it is what Jeff uses on his hair. :P
Hey Doug! I resemble that comment!

For your information, I had my hair chromed.
Years ago.
When I had a Harley.
Lord of the Bings
Post Reply